Serving western Wisconsin and eastern Minnesota

This is the foundation of your roofing system and it’s vital that you have a strong foundation that is free of rot, decay, sagging, etc. to ensure that your roofing system will be sound and will adhere to your home even in bad weather.

Installed on your eaves in 3ft courses until it reaches at least 24” beyond the inside edge of the heated wall. It is also installed in the valleys, around penetrations, chimneys, and along wall runs. Ice & water protects your home from leaks especially those caused by ice dams and snow buildup in the winter time.

Installed over your roof decking to help shield your roof decking from moisture by creating a moisture barrier between your roof decking and the roofing materials.

Installed on perimeter of your roof on the eaves and rakes to help prevent shingles from blowing off the roof.

High quality shingles that are designed to last for many decades to protect your residential home from leaks and water damage while also providing beauty and aesthetics for your home.

Installed along the ridges of your roof, continuous ridge vents are generally considered the superior ventilation method to help reduce moisture and heat in your attic which protects your home and your roofing materials against rot & decay.

Some homes do not have ridge vents and instead have metal or plastic box vents that are installed into holes cut into the roof decking to allow property ventilation which again reduces moisture and heat in the attic.

Gable vents are installed at the gable ends of the house and are cut through the exterior wall into the attic space. While gable vents are still sometimes used when building new homes, this is typically a ventilation method that is found on older homes that again is designed to reduce moisture and heat in the attic.

Installed at the hips and ridges of your roof, the hip & ridge cap shingles are the finishing touch sealing the cap of your roof and protecting your home against leaks.

Installed in the valleys and at any pitch transition points, valley metal is installed over the ice & water barrier to help protect the most vulnerable areas of your roof from water damage and leaking.

Installed around the entire perimeter of your roof eaves and rakes, drip edge helps ensure that water runs off your roof and away from your fascia to protect against water damage to your roof decking and wood fascia. If water gets behind the gutters, it will rot out both the fascia board and the roof decking causing expensive repair costs.

Installed anywhere a pitched roof meets a wall, step flashing is woven between the shingles and up along the wall run to ensure that water runs off the roof and doesn’t leak into the wall joint causing damage to your home. Step flashing is also used around chimneys and skylights.

Also known as roof to wall flashing, dormer flashing is installed wherever a roof section runs parallel to a wall run such as where a porch meets up with the siding on your home. The flashing goes under the siding on the wall and then connects down onto the roof to ensure that any water running down the wall will flow down onto and off the roof instead of getting into the joint where the roof and the wall meet.

Counter flashing is typically used around chimneys or walls runs made of brick or stone and is cut into a mortar joint to ensure that water cannot leak into the house. When flashing chimneys, there is a combination of step flashing, dormer flashing and counter flashing depending on the exterior materials of the chimney to protect your home from leaks and water damage.

Skylight flashing is vital to ensure that your skylights do not leak. A combination of step flashing and dormer flashing are installed to ensure that water runs out and away from the skylight and cannot leak into the house.

Nearly all homes have some kind of plumbing vent pipes penetrating up through the roof which require a pipe boot flashing which protects against leaks and water damage at that penetration point. The pipe boot seals tight around the pipe to ensure there are no leaks and the base of the pipe boot flashing is installed under the upper shingles and over the lower shingles to ensure water keeps flowing down and off your roof and won’t be able to get inside the house.

Similar to a plumbing pipe boot, electric mast flashing is used whenever a power line connects to a home via an electric mast pipe connected to the roof. This flashing ensures that water doesn’t leak through the mast pipe and protects your home from water damage.

Installed along siding wall runs where the roof eave meets the adjoining wall, kickout flashing is a piece of step flashing that is bent and installed in such a way as to direct the water out away from the adjoining wall to protect against leaks and water damage to your home.